How To Light A Water Heater With A Match

You need a match or a lighter to ignite the pilot gas. Depress the reset button all the way in;

How To Relight A Water Heater Pilot Light – Youtube

Table of Contents

You'll want to turn the knob past pilot to the off position.

How to light a water heater with a match. Hold down the regulator valve knob for at least one minute after the pilot has been lit. This allows the pilot flame to heat the thermocouple safety. Typically, natural gas water heaters that are manufactured before 2002 needs to be lit using a match.

Hold the flame below the the tip of the pilot tube to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites. You may need to hold down the button for up to 30 s or so birder for the thermocouple to heat up enough to hold in the pilot valve.

Place the lit match or lighter in the area of the thermocouple and press down on the button and the gas should ignite. At the bottom of the tank, you need to find and remove the inner and outer doors. Hold the button down for up to a minute to ensure that the light stays lit.

If the pilot light goes out when you release the red button, repeat steps four and five. Once the pilot light is lit, you should see a steady flame. Repeat immediately if pilot does not light on the first try.

Not sure if this is your problem? Lighting the pilot light will take about fifteen minutes. While keeping it depressed, use a wand lighter or long match to reignite the pilot light.

Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold. Apply the lighter flame to the pilot burner. If you want to light it on your own, you will need to check the heating system’s manual so you can be guided accordingly.

This will start the flow of gas so you can light the flame. The manufacturers standard re lighting steps must always be followed and then when it comes to igniting a pilot flame the bbq lighter performs the duty of what a piezo igniter could normally do. A water heater igniter has a sparking tip that is directed at the location of the pilot light.

See 'gas hot water heater troubleshooting' for a complete listing of all the possible problems and how to solve them. About press copyright contact us creators advertise developers terms privacy policy & safety how youtube works test new features press copyright contact us creators. Without the pilot light a gas hot water heater will not work and you won't have any hot water.

Continue to hold the knob down for a full minute to bleed accumulated air from the line. Hold for 60 seconds press and hold the reset or pilot button on the control box until the pilot lights, and continue to hold it for 60 seconds after the pilot is lit. Turn to on after 60 seconds, turn the control knob to the on position.

Trace the gas lines so you can easily locate where the pilot light is Do not release the regulator valve for a minute or so. How to light a pilot light on a water heater.

Repeat if necessary repeat the process once if the pilot did not light the first time. You should be able to see it above or next to the gas supply line for the pilot light. If there are more inner plates, move them as well until you see the actual pipes.

If the water heater has a manual “ignite” button, press that to light the pilot. Here are the basic steps that you will need to follow: Light a long fireplace match or butane pistol.

Using the control knob, set your water heater back to the desired temperature. For most hot water heaters, you do not have a choice. While still holding the gas down, light that pilot.

If you smell gas at any time while you are lighting your rheem. How to light an automatic water heater the first step is turning off the gas by first looking for the knob labeled on/off/pilot. There are many suggestions on preferable lighters but if you have a bbq one, it will easily reach the burner pipes for lighting a hot water heater.

The other tell tale sign is the wire that runs from the gas valve to the igniter. Turn the gas knob to “pilot,” press and hold it down. Remove the plate attached below the dial box.

Kilowatt hours wattage x hrs./1000 x cost = bill example 10,000 x 40 hrs./1000 x.05 = $20 this is a typical hot water heater lighting unplug 3” air space in back keep door gasket in good repair ranges use solar oven match pots and pans to element use min. You need to use a long match. Take a long lighter to reach the pilot.

How To Light The Pilot Light For A Water Heater – A Fix For When Water Runs Cold