You probably already have nail polish at home. All the jeweler has to do is cut a chunk of the band and weld it back together.
Getting a slightly larger ring is sensible, usually by +0.4mm increase of the id (inner diameter).
How to make a ring slightly smaller at home. Check how far the ring has slid down the mandrel after each round of hammering. This method is very visible to other people, the twine gets dirty, and it’s difficult to tie the twine off securely without leaving a bit knot and/or a long, awkward tail. Before you have your ring permanently altered, try one of these quick fixes to make your ring snug again.
Even if you need several coats, you can make your ring smaller in an hour or two, which is great if you want to wear a special ring out for a last minute event. Wrap clear scotch tape around your ring’s band to make it feel smaller. You need 3 or 4 inches of the tape to make your ring smaller.
Resizing a ring to make it smaller similarly, to make your ring smaller, a jeweler will snip the ring’s shank and cut out a small piece from the band. Pull off a piece of tape that’s roughly 2 in (5.1 cm) long. Rings that cannot be resized unfortunately, not every ring can be resized.
Pros of using nail polish to make your ring smaller. Then apply the clear nail polish over the top and to the sides of the tape. After this part of the band is removed, the two ends are then soldered back together.
Tie overhead knots one after another until the ring fits tight on your finger. A home repair would risk damaging the settings or knocking out small precious stones. And, yes, you can make your ring smaller.
If your ring is a little bit stuck on the mandrel when you’re trying to remove it, just tap it lightly in the other direction with your hammer until it loosens. To make a ring smaller, the jeweler will cut out a piece of the band, form it back into a perfect circle, and then solder it back together. To make your ring smaller using sizing beads, our jeweler simply adds two small metal balls on the back part of the inside of your ring.
This small piece of clear rubber fits snugly over the back of your ring and keeps it securely in place on your finger. Making a ring smaller is easier than making it larger—the process of downsizing is actually pretty simple. They act as an inexpensive and temporary plastic ring guard to use on rings that will soon be permanently sized.
If your ring is only slightly bent and made of a soft metal,. Give the ring a home. The plastic material prevents your ring from getting scratched.
Sizing beads are an economical way to reduce the size of your ring. Buy a plastic ring guard, available at jewelry counters and many department stores. This works best for sizing only a small amount and should be used with extreme caution when the ring has any mounted gems or diamonds.
No tools required, just snap fit the guard to the ring making your ring fit tighter… Wes gem plastic ring guards are convenient and economical to use for ring resizing. Wrap the tape tightly to the bottom par of your ring.
Peel the tape off the cutting board and press it inside the ring as shown. Start at one end of the tape and begin rolling it in a circle on top of itself, leaving enough length at the end to wrap around your ring’s band. Whenever a ring is professionally resized, it should be perfectly polished and look just as pristine as it did before the jeweler altered it.
To resize your ring smaller tie one side of a 20 inch thread to the bottom part of your ring. The jeweler will then clean the ring for a smooth and brilliant finish. You can also use hemp twine, or embroidery floss, wrapped around your ring to make it smaller.
Then the jeweler will clean it off and polish it. Remember, you can always stretch it more, but it’s difficult to shrink a ring at home. The size of your finger changes, be careful swimming in cold places as this is the most common place to lose rings.
To make your ring smaller using sizing beads, a jeweler simply adds two small metal balls on the back part of the inside of your ring. Here's how to make a ring smaller with tape. Cold water can decrease the size of your knuckle/finger by ~0.4mm id (inner diameter) in a few seconds.
If you need to use more than one thickness of tape put two small pieces of tape on top of each other and use the razor blade to cut through both at the same time to trim them to the same size. One of the most simple and traditional ways to stretch a ring and make it slightly larger is by using a mandrel and rawhide mallet. Sizing beads are an economical way to reduce the size of your ring.
In addition to any gem settings on the ring's sides, think about the hardness of its metal before attempting a home repair.