How To Measure Driver Shaft Length Without Head

Titleist will make your driver minus 4 inches or add 2 inches to stock length of 45. It involves placing the golf club on the ground and using your 48 inch ruler to accurately read how long the club or driver is.

How Long Should My Golf Clubs Be Updated 2021

Table of Contents

This increases strength and reduces weight significantly for increased distance without losing any accuracy.

How to measure driver shaft length without head. It’s time to be blunt. Keep the golf club in the playing position such that the center of the sole is in contact with the ground. The length of the shaft is measured from the top of the grip to.

Also driver shafts aren't usually tipped. In other words, put the club on the ground in address position and then measure along the bottom of the shaft. Your putter isn’t much shorter than your average driver.

Position a 48” golf club ruler behind the golf club making sure the ruler tip touches the ground by the heel of the club. Don't take this the wrong way, but if you have the head and the shaft in hand, it's pretty easy to figure out yourself to make sure. Click here for more golf fix content.

Download our instruction app from. Depending upon the lie of the driver can also contribute to the final length. You install the shaft in the head and cut the end 1/4 shorter then what you want to allow for the grip.

The distance between the “set heel end” and the “grip cap line” is the club length. Check out breed's tip on how to determine whether your driver shaft length is too long or too short by using face tape. Thorough testing is the best way to find your perfect driver shaft length.

If you tip the shaft (be careful, some shaft manufacturer's don't recommend it on certain shafts) you just do this first. Apply the sole to the plate set to the design lie angle, and set the heel end at the point of 3/8 inch from the base point of the plate. Simply hold your golf club at 45 degrees to the ground or as in your playing position.

At this point take a golf club ruler or take measure and place under the sole of the club. The length is to compensate for the lighter head. They measure club by placing the shaft flat against the wall with the toe of the driver positioned on the ground.

* putters are up to the grip end. The maximum allowable length for s driver shaft is 48 inches. Or is the measurement taken from the base of the driver head (the part touching the ground) to the tip of the grip?

For every 1/2 length reduction from the grip end there will be approximately 3 swing weights lost and the shaft will become marginally stiffer. You can (or could have) gotten the answer a lot quicker than waiting for someone to answer the post. Looking at the custom options for the drivers it looks like you can knock up to 4 off the standard length of 45.

The standard driver length of 45.5 to 46.5 inches offered by the majority of golf club companies is too long for the majority of golfers and will prevent at least 80% of all golfers from achieving their maximum potential for distance and accuracy. How to measure the length of your driver shaft: Outside of making clubs for a kid a 41 driver seems pretty darn short.

According to the united states golf association, golf clubs' overall length may not exceed 48 inches for both wood and irons. Measure to butt of grip. Use lead weight on the back of the head or lead shaft plugs in the tip to bring the swing weight back up.

It actually mimics a similar feeling to it if during your swing, but the head is noticeable lighter. Thank you if you already have the head and shaft and adapter, cutting the shaft to length should always be done by dry fitting the head in the shaft with the adapter at the desired setting and measuring out the playing length on a club ruler (it's easy to jury rig a diy club ruler if you don't have one). How to measure a golf club shaft length.

Meaning you don't cut anything off of the tip before installation. These are usually the specs you’ll get if you purchase a driver off the rack without. The best way to determine the right length for your driver shaft is to hit shots with several drivers of varying shaft lengths on a launch monitor.

This will give you you an accurate and usga standard for measuring your golf driver. The difference in length from using an adapter vs bonded will be the butt end of the shaft, that's where the cut to length would have been on the shaft. This will result in a much longer length than the other two methods mentioned before.

Having a professional measure you for a suggested club length is a plus as they can determine whether you would benefit from a custom. In fact, testing shows an inch of extra shaft length equals roughly 10 yards in distance. Use data and feel to pick your driver shaft length.

As you can tell from the above steps, measuring the length of a golf club and driver shaft is really simple. All new players should begin playing the standard length clubs unless extremely tall or short. For women’s’ drivers, they are typically one inch shorter so around 44” inches.

Heel (bottom) to top of grip. During your driver shot, you should send the ball farther than any other point in your round of golf. You don't cut the shaft to length until it's epoxied into the head so if you want to know what the actual length is without disassembling your gonna have some guesswork.

Long drivers of america method (lda) the club length is also measured by the long drivers of america (lda) method. If the shaft measure 45.75 in head without grip it should be perfect. Use a launch monitor to find out what driver shaft length performs best for you.

Just measure the playing length and subtract the length of the shaft. In general shorter shafts improve center face contact which improves consistent distance. Typically a driver shaft tip is.335, not always, but it's a very large percentage.

This will help you to understand your ball speed, club speed, dispersion, and distance.

How To Measure Golf Club Length – Man Women And Junior Golfers