How To Measure Pool Table Bumpers

Use the chart and diagram below to determine the correct size with your measurements. Take your tape measure and measure in inches between the cushion noses on the short end of the pool table (see the photo of an 8′ right).

Pool Table Terms

Table of Contents

Always measure the width as it is easier to handle and measure from the upper part of the rail.

How to measure pool table bumpers. The cuts and angles are intricate and must be exact for the table to play right. Measure the clear area around where your table will sit. Table just as easy as the lower setting.

Measure from tip of bumper to tip of bumper across the width of your pool table to find your table size. The length is typically double the width, but if it makes you feel better you can measure lengthwise, too. Sometimes, the cushions may be as much as 1/16‖ higher than the rail laminate.

K55 profile k55 cushions measure 1 ¼” across the top and 1 5/16” high at back (glue) side. This area is called the playfield. Take a measuring tape and measure the width of your table.

Measuring will take the guesswork out of sizing your felt, resulting in a faster process and a cleaner result. Take your tape measure and measure in inches between the cushion noses on the short end of the pool table (see the photo of an 8′ right). But they still look a little high to me:

Please reference the appropriate chart below to see what size cloth to order. How to measure a pool table. How can you estimate the cut angle for a shot?

The length is typically double the width, but if it makes you feel better you can measure. Playing fields, however, are standardized into four sizes throughout the industry. When planning to measure the pool table it is necessary that you have a right measuring tape.

Don’t measure under the cushion or inside the pocket. A pool table’s size designation is determined by the length and width from the inside points of the bumper cushions. So, do you want to determine the profile of your cushion?

(flying pool balls are usually not appreciated in your local tavern). We also show how to calibrate your hand so you can judge these shots (and the corresponding cut angles) fairly accurately. If you are measuring with a tape measure, place the end of the tape on the edge of the cushion.

How to measure your pool table for the proper cloth size. The cushions and rails (frame around the table) are not part of the playfield and may vary with each table site. This area is called the playfield.

Measure the playing area where the ball actually rolls on the table, from side rail to side rail. Measure from side rail to side rail where the ball hits the nose of the rail.measure from tip of bumper to tip of bumper across the width of your pool table to find your table size.measure from tip of bumper to tip of bumper across the width of your pool table to find your table size. If your table is a brunswick table and was made after 1975, then you likely require a k55 cushion, measuring 1 1/4” across the cushion top, and 1 5/16” high at the back.

How to measure pool table bumpers. Are you unsure which profile it belongs to? Most home tables feature a three piece slate play surface and the pool table rails are bolted down to this part of the table during assembly.

In addition, order extra felt. Take your tape measure and measure in inches between the cushion noses on the short end of the pool table (see the photo of an 8′ right). Measure distance from rail marker (diamond or.

If you prefer to increase the speed or bounce of your rails, set them lower… at your own risk. This is the visible wood on the rail, so you should use the same hardwood used for the cabinet. Don’t measure under the cushion or inside the pocket.

Measure your pool table before purchasing felt. Over time these bolts can become loose from vibration or if the technician did not properly torque them down originally. I wanted wide rails, so i originally attached.

The other piece to the rail is the hardwood. The easiest way to determine size is to measure the playfield width from the inside tip of one rubber bumper to the inside tip of the opposite rubber bumper. This would effectively be the width and length of your actual playing surface.

The length of your pool table will always be twice as long as its width. If using glue, pull the felt snug and determine about where the felt will match up with the edge of the slate. When you purchase the felt, or more technically the pool tablecloth , for your table, make sure it is at least 12 inches (30.5 cm) longer than the table.

As we know now that english pool tables are a bit smaller than american pool tables, you can consider measuring your pool table from both of the sides. If your table is an older one, made before 1975, be sure to measure the back side of the cushion.

Installing Pool Table Rails – Youtube