Use a bright flashlight to check your work before moving on to the next section. Start the vacuum and begin fireplace cleaning at the top of the chimney.
Lay out your dust sheet in front of the fireplace opening.
How to sweep a chimney flue. When you book your sweep, ask them to show you what’s up your aga / rayburn flue. After sweeping the chimney, a cctv survey will be carried out. If you’re cleaning from inside the house, push the brush up the chimney,.
Add more rods as you lower the brush to clean farther down the flue. Ram the cleaning brush up and down several times in a small section of the flue to remove chimney soot. Some homeowners opt to clean their own chimney flues by purchasing chimney sweeping kits.
One other chimney sweep brush type is the flat wire brush. Using one rod with the brush on, push the brush up the flue. If the chimney is too big, it may draw too slowly for a woodburning appliance and may never heat up enough to compensate.
The chimney flue is not intended to actually contain fire, only the products of fire which would be the gases that vent up through the chimney. We begin by placing a drop cloth in the work area, making sure to protect your floors and furnishings during the sweep process. Scrub the interior of the flue thoroughly.
Why it is necessary to sweep the wood burner chimney flue properly removing as much of the waste material generated from burning wood: Turn the knob completely to one side to close the flue. If you notice any of these signs, a chimney sweep or inspection is probably necessary.
If your fireplace has pull chains, pull the longer chain to disengage the damper and then pull the shorter chain to close the flue. This helps provide the scraping action necessary to get your chimney back in good shape. Smoke particles, soot and creosote, is very important.
Cut the brush down to a size a little larger than that of the flue. Point the heat source directly up the chimney for approximately 8 minutes. Reattach the chimney cap or other fitting as necessary.
This will keep the joints on the rods tight. Flat wire brushes come with toughened flat tines. Shine the light up the chimney, using the torch, to work out the size of the flue.
An annual chimney cleaning is recommended for safety reasons and to ensure the efficiency of your chimney and heating venting systems, including fireplaces, wood stoves, gas stoves, furnace flues, and pellet stoves. The chimney will be swept first to remove tar, creosote and loose parging (old lime mortar). When the furanfled liner is delivered it is bendable (like a fireman’s hose).
The best tip for how to a hire a chimney sweep is to schedule your inspection during the warmer months of the late spring or summer. If you have an aga, you probably have an open fire or woodburning stove. If it doesn’t reach all the way down, you might want to add some more cleaning rods.
If something causes a fire to start up in the flue system, say a bit of nesting is in the chimney and it catches fire, the heat can crack the flue tiles. Put on your mask and gloves. Gradually insert the brush down the chimney and into the flue to begin cleaning.
Warm the chimney up using a blow torch, or a hair dryer. A chimney extension makes sure the chimney is the proper height and the sweep can also face the top away from the direction of incoming wind, in order to improve chimney performance. Glazed or toughened creosotes are best cleaned using this brush type.
Then get them to sweep it, you may be very glad you did! By scheduling your inspection in these seasons, you’ll likely be able to have your chimney serviced sooner. The dust you wipe away is only a small part of what goes up the flue.
Certain fireplaces may feature a knob on the exterior front of the fireplace that controls the damper. The new furanflex liner can be pulled up a chimney or down from the top of the flue, which makes for easy instalment. If you want to check the inside of your flue or chimney yourself, make sure you wear goggles and a dust mask.
Do flat wire chimney sweep brushes serve for all chimney types? With the hepa vacuum on, we insert a spiral wire brush into the flue using expandable rods and slowly progress upwards through the liner and flue towards the chimney cap. Standing on the roof, the homeowner starts sweeping at top and progressively adds extension rods to a chimney brush until they reach the firebox.
Sweeping is via the soot collection door or a soot door in the vertical flue (a sweep may desire both). You must have your chimney swept and a video. In nicholasville you can’t find a chimney service more devoted to excellence in the chimney sweep industry than flue flusher.
First, the firebox is sealed with plastic to prevent debris from entering the home. Remove the brush, disassembling the rods as you take them from the flue. Then, get yourself a torch and shine it up the inside of the firebox.